Lowest Prices
up to 60% off
Same Day Shipping
on most orders
30 Day Money
Back Guarantee
Gauges
Result Pages:
Filter by Brand:
Lisle 67870 Spark Plug Gauge and Gapper - Coin-Type
Gauges and gaps all types of spark plugs from 0.20" to .100" (.50mm to 2.53mm). Tapered edge for gauging spark plugs. Specially designed hole with flange adjusts side wire of plug without pressuring center electrode.
Lisle 67950 Standard Feeler Gauge
(15) steel blades. (1) 2" steel rule. Precision blades ensure accurate measurements. Blades are approximately 1/2" W by 3-1/2" L. Skin-packed.
Lisle 68000 Mini Feeler Gauge
(16) steel blades. Precision blades ensure accurate measurements. Blades from .010" to .035" (.254-.889mm) are approximately 1/4" W by 1-3/4" L. Skin-packed.
Lisle 68050 Valve Tappet Feeler Gauge
(11) offset steel blades. Precision blades are offset at the proper angle for adjustment of valve tappets. Blades are approximately 1/2" W by 4" L. Skin-packed.
Lisle 68100 Deluxe Feeler Gauge
(31) blades. (1) brass blade .010". Precision blades ensure accurate measurements. Blades from .0015" to .035" (.038 - .889mm) thickness are approximately 1/2" W by 3-1/2" L. Skin-packed.
Lisle 68150 Go-No-Go Feeler Gauge
(22) steel blades. Precision stepped blades have a .002" step for accurate settings. Blades from .004" to .027" (.102 - .686mm) are approximately 1/2" W by 3-1/4" L.
GearWrench 162D 15 Blade SAE/Metric Feeler Gauge
Gauge measures clearances from .002 to .025" and .051mm to .635mm Blades have both SAE and metric measurements 2-1/2" rule and 15 blades Blade length: 3-5/16 in Blade width: 1/2 in Each blade has sizes marked for easy identification
GearWrench 164 Spark Plug Gap and Feeler Gauge Set
Use to set and measure spark plug gaps plus other ignition clearances from 0.010 to 0.045_ (0.254 to 1.143mm). Six wire gauges check spark plug gaps and 12 straight blades check other clearances. It includes a double-ended electrode tool for easy adj…
GearWrench 166D 6 Wire SAE/Metric Spark Plug Gap Gauge with 2 Electrode Adjusting Tools
6 Wire SAE/Metric Spark Plug Gap Gauge with 2 Electrode Adjusting Tools Use gauge to measure spark plug electrode gaps from .025" to .045" and .635mm to 1.143mm Gauge includes 2 electrode adjusting tools Most popular "standard ignition" spark plug ga…
GearWrench 2116D Disc Brake Lining Wear Gauge
Gauge measures brake lining remaining on bonded pads in 1/32" graduations Tool checks measurement without removing caliper Insert tips between the edge of the rotor and steel back up plates on the disc pads Measures from 1/8" to 3/4" and 3.1mm to …
GearWrench 2274 Metric Feeler Gauge
25-blade gauge measures clearances from 0.04 to 1mm. Blade sizes: 0.04, 0.05, 0.06, 0.07, 0.08, 0.09, 0.10, 0.15, 0.20, 0.25, 0.30, 0.35, 0.40, 0.45, 0.50, 0.55, 0.60, 0.65, 0.70, 0.75, 0.80, 0.85, 0.90, 0.95 and 1mm. Blade Lengths: 3_ long
GearWrench 3293D SAE/Metric Spark Plug Gap Gauge
SAE/Metric Spark Plug Gap Gauge Circular coin-type ramp gauge Easily measures spark plug gaps From .020" to .100" and .6mm to 2.4mm Gap spreader tool on top Convenient tether point Satin chrome finish to resist corrosion
GearWrench 3379 14mm Spark Plug Rethreader
Tool features extra-long neck for access to recessed spark plug cavities. Groove and O-ring holds tool in socket. Use with 3/8_ square drive tool or a 5/8_ socket.
OTC Tools & Equipment 5870 Injector Height Gauge Set
Injector height gauges are used to properly set injector body height to the injector follower for proper fuel injector timing. Incorrect injector timing can cause engine power issues, poor idle quality and fuel mileage issues. For use Detroit Diesel …
OTC Tools & Equipment 5870-1 Injector Height Gauge, 1.460-Inch
This mechanical gauge is used to set injector height to 1.460" (37.08 mm). For use on Detroit Diesel Two cycle 53, Two cycle 71, Two cycle 92 engines. Similar to J-1853. Sets injector height to 1.460" for proper injector timing Sets injector height…
OTC Tools & Equipment 5870-2 Injector Height Gauge, 1.484-Inch
This mechanical gauge is used to set injector height to 1.484" (37.69 mm). For use on Detroit Diesel Two cycle 53, Two cycle 71, Two cycle 92 engines. Similar to J-1242. Sets injector height to 1.484" for proper injector timing Sets injector height…
OTC Tools & Equipment 5870-3 Injector Height Gauge, 3.078-Inch
This mechanical gauge is used to set injector height to 3.078" (78.18 mm). For use on Detroit Diesel Series 60 engines. Similar to J-35637-A. Gauge has dual handle mounting locations for use on applications with Jake Brakes. Sets injector height to…
OTC Tools & Equipment 5870-4 Injector Height Gauge, 3.102-Inch
This mechanical gauge is used to set injector height to 3.102" (78.79 mm). For use on Detroit Diesel Series 60 engines. Similar to J-39697. Gauge has dual handle mounting locations for use on applications with Jake Brakes. Sets injector height to 3…
OTC Tools & Equipment 5870-5 Injector Height Gauge, 3.161-Inch
This mechanical gauge is used to set injector height to 3.161" (80.29 mm). For use on Detroit Diesel Series 60 engines. Similar to J-42665. Gauge has dual handle mounting locations for use on applications with Jake Brakes. Sets injector height to 3…
OTC Tools & Equipment 5870-6 Injector Height Gauge, 3.199-Inch
This mechanical gauge is used to set injector height to 3.199" (81.25 mm). For use on Detroit Diesel Series 60, DDEC IV engines. Similar to J-42749. Gauge has dual handle mounting locations for use on applications with Jake Brakes. Sets injector he…
OTC Tools & Equipment 5870-7 Injector Height Gauge, 3.232-Inch
This mechanical gauge is used to set injector height to 3.232" (82.09 mm). For use on Detroit Diesel Series 60 engines. Similar to J-45002. Gauge has dual handle mounting locations for use on applications with Jake Brakes. Sets injector height to 3…
Result Pages: