Dent Pullers
Result Pages:
Filter by Brand:
OTC Tools & Equipment 27315 Slide Hammer - Puller Hook
All the tools you need for flange-type rear axle and bearing removal on most late model passenger cars and light trucks. The axle bearing pullers, used with the slide hammer make it easy to remove semi-floating rear axle bearings.
OTC Tools & Equipment 898A Body and Fender Dent Puller
Body and Fender Dent Puller Often, the biggest time-consuming part of dent removal is the removal and installation of interior panels and uphol-stery. This tool eliminates those steps. Simply drill a hole at the base of the dent and thread in the too…
GearWrench 2290D Body Dent Remover
Body Dent Remover Pulls dented sheet metal back into place Drill a hole in the deepest part of the dent, insert the hook or self-threading screw tip and tap lightly with the 2 lb slide hammer to remove the dent 16.5" long shaft enables high pulling f…
GearWrench 2761 Deluxe 6" Dent Puller
Puller easily pops dented hoods, doors and fenders into place. 6_-diameter suction disc with steel handle and steel support plates enables strong pull. It works on nearly every dent where the sheet metal has not been creased. Lift edge to release suc…
Astro Pneumatic 9038 Single Suction Cup, 77 lb. Capacity
4-5/8 diameter suction cup for secure grip High impact plastic construction 77 lbs. capacity
Astro Pneumatic 9039 Double Suction Cup, 154 lb. Capacity
Dual 4-5/8 diameter suction cups for secure grip High impact plastic construction 154 lbs. capacity
Steck 20000 The Original Pull Rod Set
Super tough alloy steel is precisely heat-treatedfor maximum strength. Every Steck Pull Rod and Pick Pull is factorytested under a 500 pound (228 kg) load. Vinyl coated handle is comfortable to use.
Steck 20001 Pull Rod w/ formed shank
Super tough alloy steel is precisely heat-treated for maximum strength. Every Steck Pull Rod and Pick Pull is factory tested under a 500 pound (228 kg) load. Vinyl coated handle is comfortable to use.
Steck 20033 Quarter Puller II
Hooks above lip of the wheel opening. Two unique curvatures (one each side) to fi t most cars. Easier and faster than clamps or jacks. 3000 lb. max pull. Features 6 bars for smaller openings.
LTI Tools 800 2 pc. Inflatable Dent Remover
Uses hand pumped air pressure to push dents out. 2 piece set contains: 8 x 8 square inflatable dent remover, and 14 x 8 oblong dent remover.
H&S Autoshot DK1000 Dent Killer Attachment for Uni-Spotter Stud Welders
Upgrades any Uni-Spotter Stud Welder to a Studless Lever Action Dent Puller Quick and easy to use. How it works: The DK1000 is welded to the panel surface using your Uni-Spotter Stud Welder. The dent is levered out using only the required amount of…
H&S Autoshot DTK7700 Uni-Vac Dent Puller
A quality machined dent puller for professional use Comes with three different sized vacuum cups and a durable storage case Self-contained vacuum feature, no airlines required Can be used anywhere: inside a shop or outside on a lot Quick and easy…
AES Industries 77130 6" Vacuum Suction Disc
Ideal for lifting windshields, sheet metal, sheet plastic and glass - also pulls out dents No wetting needed Steel bar handle permits use with chain or jack Vacuum easily released without need of trigger
AES Industries 924 Suction Cup
Easily pops dented doors, fenders, hoods and trunk lids into place Also functions as a glass holder Fingertip tabs release suction instantly Powerful suction cup works on nearly every dent where the sheet metal has not been creased
AES Industries 9317 HD Pull Rod Set, Pack of 2
Repair dents and creases from the outside No need to remove interior panels or upholstery Designed for the professional with extra-large vinyl covered handles for comfort Handles are color coded Green - Straight Red - Bent
Motor Guard J20016 Motor Guard Magna Clamp
For aggressive pulling on posts and heavy-gauge sheet metal this is the heavy-duty accessory for the Magna-Spot Dent Repair Kit. Made in U.S.A.!
Mo-Clamp 1340 Bolt Puller
Made for those difficult to get at suspension and frame bolts that need the area they screw into realigned or straightened. Use this for up to a 2.5 ton pull and be certain you are dead center over the bolt area. Uses the oem bolt to pull against th…
S & G Tool Aid 81600 The Tapper 2 lb. Dent Puller
2 lb. weight slides on plated shaft. Wide handle makes it easy to rotate tool and turn puller screw into body panel. Broached nose cone prevents puller screw from turning. Nose cone and shaft threads are 3/8"-24.
S & G Tool Aid 81810 6_ Rubber Suction Cup
Use to pull out sheet metal panel dents on doors, fenders and hoods. Steel handle and reinforced steel support plate allow for maximum pull. Release suction easily by lifting lipped_ edge.
Result Pages: