Pulling Clamps
Filter by Brand:
Steck 20080 BigBite Radius Clamp
Repair damaged A-Pillar, B-Pillar, rocker and roof panels of door opening Multi-angled radius clamp with side pull ring and optional top pull ring attaches directly to the pinchweld curvature and rocker panel pinchweld for all size door openings to …
Steck 20222 Handy Pull Kit
Includes: 6mm eye bolt, 8mm eye bolt, 10mm eye bolt, right angle pulling plate and hood hinge plate and attaching ring. Eyebolts allow you to pull plates, etc. Hood hinge plate allows you to pull hood and deck lid hinges back into position. The right…
H&S Autoshot 1079 QUICK PULLER
Quick Puller
H&S Autoshot UVA400R Ultraviolet Portable Curing Unit (Mobile Repair)
Gives a full cure in 2 minutes - portable countdown timer with audible alarm 400 Watts of curing power - Largest coverage area available at 16 in. Protective glass filters out harmful UVB rays - Safety lockout switch on filter glass Safety shutters d…
Cal-Van Tools 839 6 Pc. 4WD Locknut Socket Set
This high quality steel, six-piece socket set features 1/2" square drives that enable technicians to use ratchets, breaker bars and torque wrenches in their applications. The set comes in a durable blow molded case designed for easy organization of i…
Mo-Clamp 0801 1" Tac-N-Pull Replacement Plate
Replacement adaptor plate for the #0800. 1" pull plate.
Mo-Clamp 0802 1 1/2" Tac-N-Pull Replacement Plate
Replacement adaptor plate for the #0800. 1 1/2 " pull plate.
Mo-Clamp 0803 3 Tac-N-Pull Replacement Plate
Replacement adaptor plates for the MCL-0800 3 pull plate.
Mo-Clamp 1100 Handy Link
Chain too long? Make it shorter! Chain too short? Make it longer! Alloy heat-treated steel. Pulling slots can be used with Hole Pull Adapers (#0900). Designed for use with 3/8" chain.
Mo-Clamp 1250 Panel Puller
The Panel Puller is light and easy to use with slide hammer or pulling post Use the Panel Puller on fender openings, deck lids, door posts and other openings Heat-treated alloy steel
Mo-Clamp 1300 Sill Hook
One of the handiest tools in the shop for a quick pull almost anywhere. New round opening allows for pulling with a slip hook. New casting process makes for a tighter grain structure, resulting in more strength. The original straight-cut tooth design…
Mo-Clamp 1350 Versa Hook
The Versa Hook is a versatile tool used as an outer track tie-down to secure vehicles during pulls. It is used as a pulling device for rocker panels, door posts, windshield posts, etc. Original straight-cut tooth design. Versa Hook end is 2 1/2" wide…
Mo-Clamp 1370 Curved Clamp
Specifications: Gripping surface: 7 wide, .75 deep Weight: 11 lbs. Capacity: 5-Tons Actuating jaws allow for getting around multiple angle curves and bends Heavy-Duty pull rings for both vertical and horizontal pulling Cast-in cross-hatch desi…
Mo-Clamp 1700 Chain Locking Fork
Handy stopper for chain. Used to maintain chain tension while adjusting for pulls. Locks chain tight. Heat-treated alloy steel. Designed for use with 3/8" chain.
Mo-Clamp 1800 Track Hook
Quick tie-down for track systems or back anchoring on frame racks. Lip can be used for pulling damaged areas; varied multiple uses for chain lengthening or shortening. Slot can be used for chain hook-up. Designed for use with 3/8" chain.
Mo-Clamp 1850 Inline Sllider Body Clamp
The MoClamp InLine Slider TM self-tightening clamp is made of heat-treated Tru-Tuff steel alloy. Grabs on to flanges and provides a sure grip while pulling in-line. True 5 ton pulling capacity. Finger grips are cast into the tool to provide easy hand…
Mo-Clamp 2400 3MA Strut Multi-Adapter Plate
Designed for a wide variety of strut towers. Permits fast hook-up and pulling in any direction. Allows center strut tower measurements with tram gauge instruments. Gives additional versatility for pulling over and around obstructions such as fenders.…
Mo-Clamp 3071 Mo-Ty Chain Anchor Pot
The harder you pull, the firmer it wedges. Allows full 360-degrees of pull without chain touching floor. Can be removed and installed in a different location. When correctly installed, top is flush with floor when not in use. Can be easily cleane…
Mo-Clamp 3081 T-Top II Anchor Pot
Installs using only the #3082 Installation Tool and a torque wrench. Provides a full 10 tons of pulling capacity using ?" chain. Lies flush with floor when not in use. 31/2" (89 mm) cored hole required. Heat Treated Steel. Made in the U.S.A…
Mo-Clamp 3100 4 pc. Sheet Metal Hook Set
Alloy heat-treated hooks increase pulling options. May be used with Hole Pull Plates (#0810 & #0820) to pull, or use in combination with clamps. Includes one each: #3110, #3120, #3130, #3140. Specifications: Weight approximately 2 lbs. each (.91 k…