Basic Slide Hammer May be used with an internal pulling attachment or with internal or external-internal threaded adapters. 1155 - Basic slide hammer unit is 24" long with a 5 lb. hammer and a 5/8"–18 threaded end.
Ideal for pulling jobs in very close quarters, as in removal of small bore bushings, bearings, oil seals, etc. Internal pulling attachment has jaw spread of 1/2" to 1-3/8", adjusted by turning slide hammer handle. Handle end has a 1/2"-20 thread.
Reversible-Jaw Slide Hammer Puller Extremely versatile puller, which will accomplish many pulling jobs involving gears, bearings, outer races, grease retainers, oil seals, etc. Either two or three puller jaws may be used to handle "inside" pulling jobs such as bearing cups and outer races, as well as regular "outside" pulling jobs. The basic slide hammer unit can be removed and used independently. 1176 - Puller with 2-1/2 lb. hammer, 2-way and 3-way head, 27" long. 2-Jaw Spread Inside Min. 1-1/4" Max. 3-1/2" Outside Min. 1" Max. 4-1/2" 3-Jaw spread Inside Min. 1-1/2" Max. 4-1/4" Outside Min. 1-1/2" Max. 4-1/2"
Reversible-Jaw Slide Hammer Puller Extremely versatile puller, which will accomplish many pulling jobs involving gears, bearings, outer races, grease retainers, oil seals, etc. Either two or three puller jaws may be used to handle "inside" pulling jobs such as bearing cups and outer races, as well as regular "outside" pulling jobs. The basic slide hammer unit can be removed and used independently. 1177 - Puller with 5 lb. hammer, 2-way and 3-way head, 27" long. 2-Jaw Spread Inside Min. 1-1/4" Max. 3-1/2" Outside Min. 1" Max. 4-1/2" 3-Jaw spread Inside Min. 1-1/2" Max. 4-1/4" Outside Min. 1-1/2" Max. 4-1/2"
- You can pull flange-type rear axles, remove stubborn oil seals and bearings and other press-fit parts - Puller jaws can be set up for 2/3-jaw internal or external pulling jobs - Slide hammer with 5lb. hammer - Complete set provides most common pulling attachments, more can be added - Our most popular slide hammer pulling set - The Silver Slapper 8-Way Slide Hammer Puller Set includes: the 1155 Slide hammer with 5lb. hammer, 7372 Rear axle pulling attachment, 3-way cross-head, 24545 Cone, 27241 2-way cross-block, 27315 Puller hook attachment, 34698 Pulling jaws (3) for internal or external pulling jobs, 205378 Grip wrench adapter with single lead (wrench not included), and 205377 Dent puller attachment.
Multipurpose Puller Set This assortment of puller tools gives you a wide range of job versatility. You get a 5 lb. slide hammer puller, hub puller, two sizes of OTC Grip-O-Matic™ jaw-type pullers, a bearing pulling attachment, plus a cross-bar gear and pulley puller, all contained in a handy plastic storage case. No. 1181 - Multi-purpose puller set. Set No. 1181 consists of: 1177 Slide hammer puller with a 5 lb. hammer, 2-way and 3-way heads. Reversible: either two or three jaws may be used to handle both "inside" and "outside" pulling jobs. 7208A Front hub puller for servicing front-wheel-drive cars. Includes a spare locknut, which permits use with a No. 1177 slide hammer for rear axle flanges. 1023 2-ton combination 2- or 3-jaw Grip-O-Matic puller. Has 3-3/8" max. reach, 4-3/4" max. spread. 1027 5-ton combination 2- or 3-jaw Grip-O-Matic puller. Has 5-1/2" max. reach, 7" max. spread. 7393 Bar-type gear and pulley puller with a 5-1/2" long screw. Includes two hex head cap screws, 3 /8"–16 x 3" long. Spread range: 1-1/2" to 4-1/4". 1122 Bearing pulling attachment for use with No. 1027 and No. 7393 pullers. Has 2" max spread, 1/8" min. spread.
- Components can be assembledto create several versatilepuller versions for bothinternal and external pullingtasks. - The puller head isturned to securely lock thejaws onto the part beingremoved. - Both a 2-way and 3-way puller head are included, plus three long-reach andthree short-reach puller jaws. - Plastic storage box included.Easily removes gears, bearings, timing gears, harmonicbalancers, and other pressfittedparts.
Sleeve Puller / Installer Sets: These sets work on a wide array of truck, bus, and tractor engines, as well as those in other vehicles. They'll handle wet and dry sleeves - and you won't need to remove head studs. Save time, effort, and money. - Choice of two sets: manual or 17-1/2 ton hydraulic powered. - Wide range of adapter plates available to fit most engines. Manual Sleeve Puller Set: This manually operated, screw-powered device removes cylinder sleeves from most truck, bus, and tractor engines. Adapter plates (not included in the set) accommodate a wide range of bore sizes. The puller enables one technician to handle sleeve-pulling tasks. Not recommended for MACK engines (use OTC-1202)
Pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self-threading screw tip and tap lightly with the 2-1/2-lb slide hammer to remove the dent. 13_-long shaft enables high pulling force. Slide hammer shaft has a 1/2-13 UNC thread. Handle Length: 3.75_.
- This kit provides a wide range of puller applications such as: Flange-type axles, oil seals and other press fit parts. Jaws can be set up for 2 or 3 jaw internal or external pulling jobs. - Contents: - Shallow Flange - Deep Flange - Slide Hammer - 2 Way Yoke - 3 Way Yoke - Center Bolt and Cone - 3 Pc. Adapter Set - Leg Package with Screws
Pulls flange type rear axles and most front wheel drive hubs. •Internal and external jaws provide a variety of combinations to pull bearings, gears and seals. •Two and three way cross blocks and cone provide the perfect jaw configuration for most jobs. •Set also includes a grip wrench adapter and a dent puller attachment for sheet metal or other unique pulling requirements.
Blind Hole Bearing Puller Set - For pulling jobs requiring an internal pull. - Set includes four collets, which fit a wide range of applications. Select the appropriate sized collet by comparing it with the application. Insert the collet, expand it to fit the hole, then attach the slide hammer. - Four collet sizes: 3/8" to 1/2", 9/16" to 11/16", 5/8" to 1", and 1" to 1-1/4". - Set includes a 2-1/2 lb. slide hammer with a T-handle. - Housed in a blow-molded plastic storage case. No. 4581 - Blind hole bearing puller set.
Basic Slide Hammer May be used with an internal pulling attachment or with internal or external-internal threaded adapters. 6501 - Basic slide hammer unit is 17" long with a 1-3/4 lb. hammer and a 1/2"-20 threaded end.
Ten-Pound Slide Hammer Puller This heavy-duty slide hammer puller gets tough with those really stuck parts. It has all the features of our smaller versions - heat treated, 24" long, and a 5/8"–18 threaded end to adapt to most pulling attachments. The difference is the ten-pound hammer that gives you the extra muscle for really stubborn pulling jobs. No. 7703 - Ten-pound slide hammer puller.
- 10 lb. slide weight designed for in-line impact. Balanced for continued use without fatigue. - Special hand-fit weight for ease of work. - The most complete set available! 10 of the latest and most modern engineered body pulling and pushing attachments. Consists of 16 different parts. - Dual hammer action for reverse or direct reconstruction blows. - Quick assembly for applied hook-ups on fender edges, bumper ends, rocker panels, aligning doors and door edges, hoods and hood hinges, trunk and trunk hinges, headlights and many more applications. - Rubberized hand-hold for good grip and safety. - All parts easily stored on permanent board. - Supplied with exclusive lock nut to keep attachments from rotating.
Provides excellent balance with 5lb. slide weight on plated, solid, 5/8" shaft. Exclusive soft cushion vinyl grip with "Hang-It" hole absorbs shock. Broached nose cone locks puller screw firmly in place. Supplied with body hook of heavy duty aircraft steel for pulling out curled and creased edges and panels. Helps in aligning hood and trunk hinges. Heavy duty puller screw is extra long. Designed for that in-between job where the 10 lb. Slugger slide weight is too heavy and the pullers with 3 lb. weights are too light. Nose cone and shaft threads are 5/8"-18.
The largest selling and most economical body shop dent puller in the industry. 3lb. slide weight is mounted on 12" plated steel shaft. Famous blue vinyl hand grip over steel handle reduces sting on technicnian's hands and provides 100% grip. Broached hex in nose cone locks pulling screw in place...ends breakage. Supplied with two hardened pulling screws and "L" puller hook fabricated of aircraft quality steel. Nose cone and shaft threads are 1/2"-20.